MIMAKI printer manual maintain

do you have mimaki printer, if you have, this article is very helpful for you.
MIMAKI inkjet printer repair manual...
1, MIMAKI JV22 plugging ink dl
( 1 ) , PUNCH process, the gradient of the ink off : this is caused by the ink off the ink sac and sprinklers . The rson may be the ink sac dirty , sprinklers aging, then you can cln the ink sac and nozzle, if not wash cln , replace ( water-based ink sac and spray ice clning , it is best to use pure water, especially black and red , oily available acetone ) .
( 2 ) , PUNCH process suddenly cut off the ink , and the ink off serious , if playing solid base map typically 5-10CM cut off badly, this is caused by the ink off the ink and more , the majority of replacement ink.
2.MIMAKI inkjet printer ink nozzle back on the big stack sound approach
(1), caping wipping flashing value is too small , the more points you can transfer large value .
( 2 ) , ink jet car in contact with the top of the stack section dirty or corroded , cln fuel solved.
(3), cap base malposition , to be adjusted .
3 , there is a set of test strips not playing , but can be washed ink
( 1 ) , this phenomenon may be 20 # blown fuse should be replaced .
( 2 ) Check the nozzle and nozzle control panel data cable to connect with the motherboard .
4 , play no test strip processing methods
( 1 ) , and the der decoding of disloion , and the der de the calibration strip .
( 2 ) , was detected in the TEST der to see if ed.
( 3 ) , # 35 on the motherboard blown fuse after fuse need to be replaced from time to time to check whether the motherboard cable is damaged sprinklers and sprinkler control panel 6 transistor brkdown, if the transistor brkdown, play diagram, but playing in Figure 5-10CM, 20 # and blows , and the ht sink temperature is higher.
5 , hit the test strip , the play is a set of nozzles several colors color processing :
( 1 ) Check the nozzle data cable is damaged
( 2 ) , replacement sprinkler nozzle check for damage
6 , there is an uneven playing striped figure dl
( 1 ) , replace the print line
( 2 ) Check whether the decoding of sagging
( 3 ) , replace the decoding of
7 , during the playing figure drops of ink dl
( 1 ) , on the need to remove debris glue nozzle
( 2 ) , scraping the bottom of the car and sprayed too close , the adjusted value wipping pos
8 , no less than the red ink trtment
( 1 ) , pumping hose rupture in need of replacement ink or improperly installed hose pumping ink
( 2 ) , pumping hose or hose ink ink ink solidifiion stack
( 3 ) , not put away the sponge
( 4 ) , the hd and the ink stack fit well, the need to adjust the value caping wipping flashing
( 5 ) , the nozzle surface deformation , to be replaced
( 6) the need to replace the ink stack deformation
9 , sprayed side of the car to move the process wipes , while not wipes
( 1 ) , the paper did not put away
( 2 ) a fixed spray car slider loose screws
10 , playing some kind of figure out the process of multi- color thin line trtment: replacement nozzles, nozzle check for damage
11 , hit the edge with long spines Figure phenomena or side striped bottom nozzles need clning dirty
12 , no panel display processing
( 1 ) , the panel power light is not lit , check the motherboard to motherboard after unplugging the power cord to see if the power supply fan rotation is normal, if normal rotation mostly motherboard ed
( 2 ) , a display panel at first but when you start plse wait no display , this phenomenon is more for the Y -axis motor damage
( 3 ) , motherboard no display, but the power light stays lit , check the motherboard CN21 data cable is damaged stagnation
( 4 ) , a large capacitor check the motherboard data cable is loose or ed down , replace the motherboard
( 5 ) Check the power supply board is ed
13 , while playing normal color chart , while not normal processing
( 1 ) Check whether the decoding of sagging
( 2 ) , replacement ink sac
( 3 ) , the initialization
14 , there are rules to play a square dl with the process diagram
( 1 ) , replace the computer
( 2 ) initialize
15 , the plot on the phenomenon of ink sponge processing
( 1 ) Check whether the loion misplaced sponge
( 2 ) , the stack of the ink tube to check whether the block
16 , reported missing ink processing machines
( 1 ) , check the sensor , the position of the sensor cartridge
( 2 ) Check the sensor cable is damaged
17 , reported ERROR41 error handling machine
( 1 ) Check whether the belt is too tight
( 2 ) , the replacement of the Y-axis motor
( 3 ) , belt scared, stuck to replace the belt for
( 4 ) , belt scared, stuck to replace the belt for

18 , reported ERROR40 error handling machine
( 1 ) , check the X -axis turbine damage
( 2 ) , the replacement of the X-axis motor
19 , reported press ent machine error handling
( 1 ) , before checking the sensor is loose cover
( 2 ) whether the car hit the spray nozzle check back position sensor return when
( 3 ) Check whether the belt is too tight
( 4) Replace the Y axis motor
20, MIMAKI printer machine reported ERROR20 error handling : Unplug the data receiver, see if you can bt the test strip properly , if compared to the data receiver board is damaged ; does not , then the damage to the motherboard .
21 , reported ERROR50 error handling machine
( 1 ) , the paper put too right ,
( 2 ) , the transparency of the sheet of paper is too large , or the replacement of the mat material having the following material
( 3 ) , replace the bad paper sensor paper sensor
( 4 ) , paper low sensor sensitivity adjustment # PARAMETER → SYSTEM value of 10 = 50ELV
( 5 ) , paper sensor with an alcohol wipe dirty paper sensor
22, MIMAKI JV22 inkjet printer machine reported ERROR 007 Temp n machine detects abnormal temperature error handling
( 1 ) , the machine version 1.6 or more and will have a bad hd down version 1.6
( 2 ) , the machine version 1.6 or fewer than six sprinklers will replace lost or sprinklers will make up a small nozzle
23 , the machine reported Error 45 Caping wrong
(1), Caping sensor with an alcohol wipe dirty look Caping sensor
(2), Caping sensors fall reinstall Caping sensor
(3), Caping sensor is bad if a foot , with the double-sided adhesive sensor replacement Caping
24 , the print screen has distorted
( 1 ) , the decoding section de clning dirty or der or a der of
( 2 ) , the picture in question to re- RIP Pictures
25, MIMAKI printer machine reported Error 51 Y ORGIR wrong
Spray vehicle sensor is dirty or bad jet car sensor replacement or clning spray vehicle sensors